Highlights
  • Host Bus: PCIe x4 Gen 2 (20.0 Gb/s), Low-Profile PCI Form Factor
    • Compliant with PCI Express Base Specification Revision 2.0
  • It supports the following SFP+ modules types which meet SFP+ specification:
    • 10GBASE-LRM/10GBASE-SR/10GBASE-LR/1000BASE-SX/1000BASE-LX/10GBASE-ER
    • SFP+ active copper direct attach cable (AOC)
    • SFP+ passive copper direct attach cable (DAC)
  • Virtual NIC support
  • Reduced CPU utilization and improved throughput
  • Ethernet and Media support
    • Jumbo frame support (16K)
    • Full IEEE Std 802.3ae Compliant
    • IEEE 802.1Q VLAN
    • RFC 2819 RMON MIB Statistics
    • Multicast
    • IEEE 802.3ad Link Aggregation
  • Performance enhancements
    • Microsoft Scalable Networking
    • Receive-side scaling (RSS)
    • MSI
    • IP, TCP and UDP checksum offloading
    • Large Send (up to 64 KB)
    • Low Latency (< 4 uS)
Introduction

SFP10G-PCIE4XG201 is 10 Gigabit Ethernet SFP+ to PCI Express x4 Gen 2 Host Card .

The SFP10G-PCIE4XG201 complies with common 10GbE SFP+ optical & Direct Attached Copper modules. 
With only 4.12 Watts maximum power consumption (including the optical module in full duplex), the SFP10G-PCIE4XG201 offers the lowest power consumption and the best cost solution in the market today.
Targeted at high-end Workstations and low cost Application Servers, which seek to service the increasing demand of higher network bandwidth, while maintaining low power and cost budgets.
Technical Specifications
PCI Express
  • PCI Express Rev 2.0 specification (5 GT/s)
  • PCI Express Gen2 x4 Host Bus interface
Ethernet Feature
  • 10 Gigabit performance
  • Ethernet and Media support
    • Jumbo frame support (16K)
    • Full IEEE Std 802.3ae Compliant
    • IEEE 802.1Q VLAN
    • RFC 2819 RMON MIB Statistics
    • Multicast
    • IEEE 802.3ad Link Aggregation
  • Performance enhancements
    • Microsoft Scalable Networking
    • Receive-side scaling (RSS)
    • MSI
    • IP, TCP and UDP checksum offloading
    • Large Send (up to 64 KB)
    • Low Latency (< 4 uS)
  • Full Duplex
Power Input
  • Voltage: 3.3V & 12.0V
  • Power consumption: 4.12W (Full bidirectional traffic, 100m cable, 10G speed)
LED Indicators
  • Link / Activity
Number of Port
  • SFP+ 20pin Connector
Computer Platform
  • Computer with PCI Express slot ( x4, x8, x16)

    • Note:
    For the best performance (5.0 Gbps), SFP10G-PCIE4XG201 should be installed in a PCIe Gen 2 compliant slot in the host computer.  Most computers have PCIe Gen 2 (5.0 Gbps) throughput on x8 or x16 slots.
    A PCIe Gen 1 compliant slot reaches up to 2.5 Gbps throughput.
Operating System Requirements
  • Windows 7, Windows 8
  • Windows Server 2012, Server 2008 R2
  • Linux 2.6.x, Linux 3.x
  • VMWare® 5.x,
  • Hyper-V®
Physical Dimensions
  • 63.5mm(H) x 83.6mm(L)
  • NW: 42g
Related Products

10G Ethernet SFP+ Active Optical Cable

more information

10G Ethernet SFP+ Passive Cable

more information

CO-M0368/CO-M0418 SFP+ module

10Gb/s SFP+ optical transceivers are designed for use in 10-Gigabit Ethernet links over multimode fiber. They are compliant with SFF-8431, SFF-8432, IEEE 802.3ae 10GBASE-SR/SW and 10G Fibre Channel 1200-Mx-SN-I. Digital diagnostics functions are available via a 2-wire serial interface, as specified in SFF-8472. The SFP+ module is a "limiting module", i.e., it employs a limiting receiver. 

  • Hot-pluggable SFP+ footprint
  • Supports 9.95 to 10.5 Gb/s bit rates (contact Finisar for higher data rate support)
  • Power dissipation < 1W 
  • Single +3.3V Power Supply
  • Maximum link length of 300m on 2000 MHz-km MMF
  • Uncooled 850nm VCSEL laser
  • Receiver limiting electrical interface
  • Duplex LC Type connector
  • SFF-8472 Digital Diagnostic Function
  • Commercial Operation Temp.: 0°C to 70°C

 
Kit includes
  • SFP10G-PCIE4XG201
Optional Accessories
  • Low Profile PCI Bracket
    • S-BR-00194-17-1020