Highlights
  • Host Bus: PCIe x4 Gen 2 (20.0 Gb/s)
    • Compliant with PCI Express Base Specification Revision 2.0
  • Four independent USB 3.0 Host Controllers (Fresco FL1100, USB IF TID 380000026)
    • Compliant with USB 3.0 Specification 1.0
    • Compliant with Extensible Host Controller Interface (xHCI) Specification revision 1.0
    • Support SS/HS/FS/LS data rates (5Gbps/480Mbps/12Mbps/1.5 Mbps)
  • Supports UASP (USB Attached SCSI Protocol)
  • WHQL certified driver support for Windows 8, Windows 7, Windows Vista and Windows XP
  • Linux xHCI support under Linux kernel version 2.6.31 and after
  • Four USB 3.0 Cable Ports with USB 3.0 cable port lock mechanism
    • Three A-type Receptacle, USB IF TID 360000006
      • USB 3.0 Vision Standard cable port lock mechanism (pitch: 22mm)
    • One Right A-type Receptacle, USB IF TID 360000055
      • IOI Standard cable port lock mechanism
  • EMI: ESD Air ±15KV, Contact ±8KV
  • USB Bus Power Input: 12V Step-Down to 5V from either PCIe 12V or Power Connector 12V
Introduction

The U3X4-PCIE4XE314 is a Quad channel USB 3.0 to PCI Express x4 Gen 2 Host Adapter.

U3X4-PCIE4XE314 is designed with Two key components.

  • 8-Lane, 6-Port PCI Express Switch.
  • PCI Express to USB 3.0 Single Chip Host Controller (FRESCO FL1100, USB IF TID 380000026).

Utilizing the standard PCI Express Switch, the 8-Lane/6-Port PCI Express Switch provides the most efficient fan-out solution for integrating four PCI Express to USB 3.0 Single Chip Host controllers into a small board design. Each USB 3.0 to PCI Express Single Chip Host controller takes advantages of 5 Gbps burst rate of 4-lane PCI Express bus in both directions and is fully compliant with PCI Express Base specification r2.0. This solution provides full PCI Express and USB 3.0 functionality and performance.

Technical Specifications
PCI Express
  • Standards compliant
    • Compliant with PCI Express Base Specification Revision 2.1
    • Compliant with PCI Express CEM Specification Revision 2.0
    • Compliant with PCI-to-PCI Bridge Architecture Specification Revision 1.2
    • Compliant with Advanced Configuration Power Interface (ACPI) Specification
    • PCI Power Management Spec r1.2
  • PCI Express Power Management
    • Link power management states: L0, L0s, L1, L2/L3 Ready, and L3
    • Device states: D0 and D3hot
    • Active state power management for L0s and L1 states
  • Port Arbitration Round Robin (RR) and Weighted RR and Time-based Weighted RR
  • Extended Virtual Channel capability
    • Two Virtual Channels (VC) and Eight Traffic Class (TC) support
    • Independent TC/VC mapping for each port
    • Provides VC arbitration selection: Strict Priority, Round Robin (RR) and Programmable Weighted Round-Robin
  • Supports Isochronous Traffic
    • Isochronous traffic class mapped to VC1 only
    • Strict time based credit policing
  • Supports “Cut-through”(Default) as well as “Store and Forward” mode for switching packets
  • Peer-to-peer switching between any two downstream ports
  • Supports up to 512-byte maximum payload size (setting to 256-byte)
  • Enhanced Features
    • 150ns typical latency for packet running through switch without blocking
    • Supports Access Control Service (ACS) for peer-to-peer traffic
    • Supports Address Translation (AT) packet for SR-IOV application
    • Supports OBFF and LTR
USB Features
  • Compliant with USB 3.0 Specification Revision 1.0
  • Compliant with Extensible Host Controller Interface (xHCI) Specification revision 1.0
  • 4 downstream USB ports support SS/HS/FS/LS data rates (5Gbps/480Mbps/12Mbps/1.5Mbps)
  • Supports UASP (USB Attached SCSI Protocol)
  • Supports xHCI debug capability
  • Support for Ultra High-performance isochronous applications
  • Support for Latency Tolerance Tolerance Messaging (USB)
Advanced Power Saving
  • Support all USB 3.0 Power States: U0, U1, U2 and U3
  • Support USB 2.0 Link Power management (LPM)
    • USB-IF LPM PDK Standard
  • PCIe Active State Power Management (ASPM) L0s and L1
USB3 cable lock mechanism
  • Provides the threaded holes for the jack-screws of USB 3.0 A Plug w/Jackscrew lock Cable
    • 3-port USB 3.0 Vision Standard cable port lock mechanism or IOI Standard cable port lock mechanism
    • 1-port IOI Standard cable port lock mechanism

USB Bus Power Input

  • 12V Step-Down to 5V from either PCIe 12V or Power Connector 12V (ATA 4-pin or SATA 15-pin)

    The USB Bus power (5V) are step-down from 12V and the 12V input might from either PCIe Edge Connector or Auxiliary Power Connectors (J1 & J2).
    Note:
    If the PCIe Slot can’t supply 12V current high enough then you have to attach the Auxiliary Power from either J1 (ATA 4-pin) or J2 (SATA 15-pin).

Computer Platform

Computer with PCI Express slot ( x4, x8, x16)

Note:
For the best performance (5.0 Gbps), U3X4-PCIE4XE314 should be installed in a PCIe Gen 2 compliant slot in the host computer.  Most computers have PCIe Gen 2 (5.0 Gbps) throughput on x8 or x16 slots.
A PCIe Gen 1 compliant slot reaches up to 2.5 Gbps throughput.

Operating System Requirements
  • If OS is Windows 8 or later , there are inbox driver for Fresco USB 3.0 Host Controller.
  • Linux xHCI support under Linux kernel version 2.6.31 and after
  • USB 3.0 Host Drivers
    x86 (32-bit) and x64 (64-bit)
    • Windows XP
    • Windows Vista
    • Windows 7
    • Windows 8 and 8.1
Certifications
  • CE Test: Pass
  • FCC Test : Pass
  • VCCI Test: Pass
  • RCM Test: Pass

      

Physical Dimensions
  • 103mm(H)x115mm(L)
  • NW: 77.5g (Unit Package:150.5 g)
Kit includes
  • U3X4-PCIE4XE314
  • Driver CD