Introduction

U2H4+PSATA11S is an USB 2.0 four-port HUB with one USB to ATA/SATA bridge. U2H4+PSATA11S provides three downstream USB ports, one IDE (ATA/ATAPI) port and one SATA port. It is ideally suited for docking station solution which need more USB port and interface for connecting two ATA/SATA devices.

It allows ATA/SATA drives (Master and Slave) to be connected to USB 2.0 serial bus in a plug-and-play fashion.

The bundled backup software provides the perfect solution for data backup and transferring of data between computer and ATA/SATA HDD.

Technical Specifications

U2H4+PSATA11S combines two key components:
 1). Four ports USB 2.0 High Speed Hub
2). USB 2.0 to ATA/SATA Bridge Board

1). Four ports USB 2.0 High Speed Hub:

U2H4+PSATA11S provides four downstream USB ports, with Single Transaction Translator (STT) for all ports, making it the cost effective hub solution.

The U2H4+PSATA11S works backward compatible either when any one of downstream ports are connected to an USB 1.1 compliant device, or when the upstream port is connected to a USB 1.1 compliant host.

  • Compliant with USB 2.0(Data Rate 1.5/12/480Mbps)
    4 downstream ports
    • Two downstream ports (USB1&2) are Intel block berg-strip header (2x5/9 pin).
    • One downstream port (USB3) is Intel block berg-strip header (2x5/9 pin).
    • One downstream internal port for USB 2.0 to ATA/SATA Bridge Board
  • Single transaction translator (STT)
    • Single transaction translator share the same TT control logics for all downstream port devices.
  • All downstream facing ports can handle high-speed (480 Mbps), full-speed (12 Mbps), and low-speed (1.5 Mbps) transaction.
  • Self-powered mode operation.
  • Supports Over-current detection and Individual power control
  • DC Power Connector: Floppy Disk Drive like mini 4-pin DC power connector
  • USB 2.0 Interface: USB B-Type connector

2). USB 2.0 to ATA/SATA Bridge Board:

  • IDE(ATA) Interface: Header 20x2 pin
  • Serial ATA port: Signal (7pin) type connector
  • Serial ATA Bus Transfer Rate: 1.5 Gbps
  • Supports hot-plug & hot-swap feature of Serial ATA to USB.
  • USB Bus Transfer Rate: High Speed (480 Mbit) And Full Speed (12 Mbit)
  • Self-powered mode operation.
  • Complies with T13's ATA/ATAPI-6 Draft Specification:
    • PIO Mode 0 ~ 4
    • Multi-Word DMA Mode 0 ~ 2
    • Ultra DMA Mode 0 ~ 5
    • Supports 48-bit addressing for large hard drives (>128GB)
  • Complies with Gen1i and Gen1m of Serial ATA II Electronic Specification 1.0
  • Power indicator LED and ATA/SATA Access LED
Physical Dimensions
  • 89.5 mm (W) x 62 mm(D)
  • Form Factor
    • SCSI I 50pin Low Density Centronics Connector
    • Fit to most standard SCSI enclosure
Kit includes
  • U2H4+PSATA11S Bridge Board
  • CB-00136 - A Plug -to- B Plug USB 2.0 cable in length of 1.5m
  • CB-00292 - Ultra DMA100 Cable 12+6 inch for two devices (Black - Gray - Black)
  • CB-00334 - SATA plug to SATA plug Cable in length of 50cm (w/Latch)
  • CB-00385 - SATA 15 pin to IDE Big 4 pin power Connector in length of 15cm
  • Installation Guide
  • CD-tilte (Driver for Windows 98/98SE, Backup Software)

Option:

  • CB-00281 - Intel Block Standard 5x2/9pin Housing to two USB B Plug Cable
  • CB-00378 - Intel Block Standard 5x2/9pin Housing to one USB B Plug Cable

 
Certifications
  • CE Test: Pass
  • FCC Test : Pass
  • VCCI Test: Pass
  • BSMI Test: Pass