Highlights
  • USB 3.1 Gen 1 4-port Hub, TID#330000056
    • Supports USB 3.0 SuperSpeed (5Gbps), USB 2.0 Hi-Speed (480Mbps), Full-Speed (12Mbps), and Low-Speed (1.5Mbps)
    • Upstream port: USB3 B-Type Connector
    • Downstream port: USB3 A-Type Connectors
  • Two USB 3.1 Gen 1 to SATA III Bridges, TID# 340870005
    • Serial ATA bus Signal bandwidth: SATAIII (6Gbps)
    • SATA 7-pin (Vertical) Connector
  • Provides Jumper for Read-only (Write Protect) or Read/Write selection
  • Self-Powered (Needs DC Power Input from Big IDE 4-pin DC Power Connector or Floppy drive like mini-4pin power connector)
Introduction

U3H41S2310S provides two downstream USB 3.1 Gen 1 ports and two SATA device ports.
It is ideally suited for tailgate interface applications for two SATA drives and two USB devices.
It allows SATA drives and USB devices to be connected to USB 3.1 Gen 1 serial bus in a plug-and-play fashion.
U3H41S2310S provides a cost-effective solution for system integrator to integrate two SATA drives and two USB devices into their system through the USB 3.1 Gen 1 serial bus.

U3H41S2310S provides a Jumper which allow user to set the function for selecting SATA Read-only (Write Protect) or Read/Write.
Specification

U3H41S2310S integrates two key components:

1). USB 3.1 Gen 1 HUB (Four USB 3.0)
2). Two USB 3.1 Gen 1 to SATA III Bridge Controllers

1). USB 3.1 Gen 1 HUB (Four USB 3.0)

  • USB 3.1 Gen 1 Compliant Hub, TID#330000056
    • Upstream Port Supports SuperSpeed USB, High-Speed and Full-Speed Connections
    • Supports Four Downstream Ports
    • Each of the Four Downstream Ports Support SuperSpeed USB, High-Speed, Full-Speed/Low-Speed Connections
  • USB 2.0 Hub Features
    • Multi Transaction Translator (MTT) Hub: Four Transaction Translators
    • Two Asynchronous Endpoint Buffers Per Transaction Translator
  • Upstream port: USB3 B-Type Connector
  • Downstream ports
    • Two downstream: USB3 A-Type Connectors
    • Two downstream: USB3 ports which integrated two SATA Bridges
  • Supports Spread Spectrum Clock (SSC)
  • Provides Upstream Connection status LEDs (SuperSpeed and High-Speed):
    • High-Speed status LED
      • Off = Hub in low/full speed mode
      • On  = Hub in high-speed mode
    • SuperSpeed status LED
      • Off = Hub not in SuperSpeed USB mode
      • On = Hub in SuperSpeed USB mode

2). Two USB 3.1 Gen 1 to SATA Bridge Controllers

  • USB 3.1 Gen 1 to SATA Bridge: ASMedia ASM1153E (TID# 340870005)
  • Serial ATA bus Signal bandwidth: SATAIII (6Gbps)
  • Compliant with USB 3.0 Specification Revision 1.0
  • Compliant with USB Specification Revision 2.0
  • Supports USB Super-Speed/High-Speed/Full-Speed Operation
  • Supports USB Mass Storage Class, Bulk-Only Transport Specification Revision 1.3
  • Support UASP( USB Attached SCSI Protocol) Specification Revision 1.0
  • Complies with Serial ATA Specification Revision 3.0
  • Support SATA Hot-Plug
  • Support ATA/ATAPI Packet Command Set
  • Support ATA/ATAPI LBA48 addressing mode
  • Integrated 8-bit micro-processor with embedded program RAM and ROM
  • Support SPI NVRAM for Vender Specific Application of USB Device Controller
  • SATA 7-pin (Vertical) Connector
  • Support Write Protect for HDD
    • Read-only (Write Protect) or Read/Write Setting Header
  • LEDs:
    • Write Protect LEDs Headers
    • SATA activity LED Headers
  • Support Spread Spectrum Control of USB 3.1 Gen 1 and SATA interface to improve the EMI performance
Physical Dimensions
  • 83.3mm x 21.56mm x 68mm
  • SCSI 1 50pin Low Density Centronics Connector Form Factor. (Fit to most standard SCSI enclosure)
Kit includes
  • Bridge Board
  • Overview