Highlights
  • 5.25" ODD (Optical Disk Drive) form factor
  • Two 5V/32-bit PCI slot
  • Provides four different Pin-selectable frequency (25, 50, 33, 66 MHz) options for PCI clock
Introduction

IP1X-P32X20 is a PCIe x1 to PCI (two 5V/32-bit slot) docking system and integrated by the following three key parts: IPCIE1XCA01, DB525-PCIE1XP32X20 and CB-00592.

  • IPCIE1XCA01
    • Internal PCI Express x1 cable adapter
  • DB525-PCIE1XP32X20
    • PCIe to PCI (two 5V/32-bit slot) docking bridge
  • CB-00592
    • 2-in-1 female (10X2_19pin) USB 3.0 Internal cable

IP1X-P32X20 includes a PCI Express x1 to PCI (32bit/66MHz) bridge with high performance and low power consumption. The typical usage for this device is for applications that require a “bridge” from legacy PCI products to new PCI Express based systems.
DB525-PCIE1XP32X20 provides two PCI 5V/32-bit slots and one single-lane Internal PCIe port (IOI Proprietary) for connecting to the PCIe cable adapter (IPCIE1XCA01) through CB-00592.  DB525-PCIE1XP32X20 is designed with the standard size of 5.25" ODD form factor so it can be installed into a PC case with a free 5.25" bay.

Technical Specifications

IPCIE1XCA01

Primarily PCIe interface
  • 1-lane PCI Express

Secondary PCIe interface
  • One single-lane Internal PCIe port (IOI Proprietary)
    • 10X2_19pin Header (Pitch=2.0mm)

DB525-PCIE1XP32X20

Upstream host connector
  • 1-lane PCI Express
    • PCIe Gen 1: 2.5 Gbps
  • One single-lane Internal PCIe port (IOI Proprietary)
    • 10X2_19pin Header (Pitch=2.0mm)

Downstream Internal PCI bus interface
  • Two PCI slot (32-bit/33Mhz or 66Mhz)
PCI Express features
  • Compliant with PCI Express Base Specification, Revision 1.1
  • Compliant with PCI Express Card Electromechanical Specification, Revision 1.1
  • Compliant with PCI Express to PCI/PCI-X Bridge Specification, Revision 1.0
  • Physical Layer interface (x1 link with 2.5Gb/s data rate)
  • Lane polarity toggle
  • Virtual Isochronous support (upstream TC1-7 generation, downstream TC1-7 mapping)
  • ASPM support
  • Beacon support (but does not support WAKE# signal during power management)
  • CRC (16-bit), LCRC (32-bit)
  • ECRC and advanced error reporting
  • Maximum payload size to 512 bytes
PCI features
  • Compliant with PCI Local Bus Specification, Revision 3.0
  • Compliant with PCI-to-PCI Bridge Architecture Specification, Revision 1.2
  • Compliant with PCI Bus PM Interface Specification, Revision 1.1
  • Compliant with PCI Hot-Plug Specification, Revision 1.1
  • Compliant with PCI Mobile Design Guide, Version 1.1
  • 3.3V PCI signaling with 5V I/O tolerance
  • Provides two level arbitration support for four PCI Bus masters
  • 16-bit address decode for VGA
  • Subsystem Vendor and Subsystem Device IDs support
  • PCI INT interrupt or MSI Function support
General features
  • Compliant with Advanced Configuration and Power Interface Specification (ACPI), Revision 2.0b
  • Forward bridging (PCI Express as primary bus, PCI as secondary bus)
  • Transparent mode support
  • Power Management (including ACPI, CLKRUN_L,CLKREQ_L, PCI_PM)
  • EEPROM (I2C) Interface
  • Auxiliary powers (VAUX, VDDAUX, VDDCAUX) support
  • Power consumption less than 0.45 Watt in typical condition

Power connector
  • One SATA 15pin power connector
    Note: DB525-PCIE1XP32X20 requires power (+12V, +5V, +3.3V)
Form factor
  • 5.25" ODD (Optical Disk Drive) form factor
  • 146.6(W) x 42(H) x 177.5 (D) mm
  • NW: 380g
Applications
Legacy PCI products to new PCI Express systems.
Model No: IP1X-P32X20
  • IPCIE1XCA01
  • DB525-PCIE1XP32X20
  • One Cable CB-00592
Kit includes

IP1X-P32X20

  • DB525-PCIE1XP32X20
  • IPCIE1XCA01
  • CB-00592
  • Overview